MG-Cars.net

Welcome to our resource for MG Car Information.

Recommendations

Parts

MG parts spares and accessories are available for MG T Series (TA, MG TB, MG TC, MG TD, MG TF), Magnette, MGA, Twin cam, MGB, MGBGT, MGC, MGC GT, MG Midget, Sprite and other MG models from British car spares company LBCarCo.

MG TD TF 1500 - Wiper Knob Grub/Set Screws

Anyone know what the grub/lock screw for the TF wiper knob thread and size is? I actually need 2. PJ
Paul S Jennings

Most likely a 2BA screw - if larger than that then a 1/4 BSF, smaller would be a 4BA. Cheers - Dave
D W DuBois

Hi Paul, I don't think the knob is threaded. A 4BA machine screw goes through the hole in the knob and this screw is threaded into a hole in the wiper gearbox shaft. At least that is what I have on mine.
Cheers, Hugh
H.D. Pite

PJ
Can you put up a picture of your knob
I also may have one but am not sure if it is TF or not. Just one of the many things I have in my box of bit collected over the years.
Hopefuly not all just left over bits :)
Rod

Rod Jones

Wiper knobs on my TF are secured with a cheese head screw, thread profile unknown without radical dismantling. I believe these are original. The knobs are not threaded, the screw head is captive in a recess and secured via the thread in the gearbox shaft.

Graeme
G Evans

Thanks guys, much appreciated information!
Rod, I'll get a photo of it later today and post it. Believe it or not, I haven't yet compared the repo to my original. Later today. PJ
Paul S Jennings

Hi guys
Here is a photo of a knob and its set screw. Yes, the knob has no threads. It attaches like Hugh states.

Tom
'54 TF


T Norby

If that is the correct screw, it is a 2BA, the same as used on the SU fuel pumps to hold the coil housing to the pump body. Cheers - Dave
D W DuBois

Here is a picture of a 4 BA machine screw threaded into the hole in a wiper gearbox shaft. I think 2 BA is too large to thread into the 1/4" shaft and have any strength left.
Hugh Pite


H.D. Pite

Tom, Here's the repo. PJ


Paul S Jennings

where can the correct screws be bought?
J K Barter


If if is a 4BA, and I can't guarantee that, then its very close to a UNF 6-40.
The 4BA has dimensions of 0.142 by 38.5 TPI
The 6-40 had dimensions of 0.138 by 40 TPI.

While not common, you can get panhead 6-40 screws at McMasters.

http://www.mcmaster.com/#machine-screws/=tht285

On my TD I did find some 5BA screws. I think, but I am not sure it might have been on the Wiper Motor.
The UNC 5-40 is a good enough fit for these.
5ba is 0.126 by 43 TPI
5-40 UNC is 0.125" by 40 TPI.
If it is a 5BA a 1/8 drill should just fit in the threaded hole.
If it is a 4BA a number 29 drill should just fit

Should it be a 5BA I have a box of 5-40 by 1/4" long and I would be more than happy to send a few.

Jim B.
JA Benjamin

Paul, the repro is a great likeness of the original. I believe mine are original. They have the brown hue of bakelite.
It is a simple design. It seems someone could make a mold and reproduce some. Anyone have a 3D printer?
It seems that this one TF part is unobtainable. I sure would like to have an extra.
Anyone out there have the capability to make some?

Tom
'54 TF
T Norby

British Tools & Fasteners has these in 4BA X 1/2 inch. Are they what I need? PJ






Paul S Jennings

Paul
The screw in my photo above is 1/2 inch.
Tom
T Norby

Thanks Tom, I'll order a couple. PJ
Paul S Jennings

This thread was discussed between 29/08/2014 and 30/08/2014

MG TD TF 1500 index

This thread is from the archive. The Live MG TD TF 1500 BBS is active now.